SPECIFICATION
Model
Power Control
HOUSEHOLD USE ONLY
SC-B550
SC-B555/B555T
With power control/
Without power control/
NAME AND FUNCTION OF PARTS (Assemble as indicated in the center illustration.) /
Vacuum Power Adjustment Ring /
Dust Indicator /
Extension Pipe/
Hose Stopper/
Unclogging the Hose /
The full vacuum power of the cleaner may be too strong in certain
cases, for instance when vacuuming curtains and draperies. In
these cases, turn the vacuum power adjustment ring (on the hose)
to control the vacuum power. Match the hole in the ring with
the hose hole to reduce the power.
The dust indicator shows the amount of dust that has been collected in the dust
compartment. Hold the floor nozzle away from the floor, while operating to check.
The pipe is adjustable according to the height of the user.
Insert the hose stopper all the way up to the air inlet.
When the hose is clogged with dust, remove it in the following
manner:
1) Pull out the angled pipe by turning the removal ring in either
direction.
2) Use a vinyl garden hose to push out the dust clogging the
hose.
To detach it, press button on the hose stopper
and pull the hose toward you.
Button
(How to expand/contract the pipe)
Adjust thelength of the pipe while pushing the button in.
Make sure that youhear a "clicking" sound.
Connect the angled pipe
DUST INDICATOR
DUST INDICATOR
3) Insert the angled pipe in place and return the ring to its
original position.
Do not use the hose without the angled pipe in place. If the
hose is used without the angled pipe, the hose will bend
excessively, causing it to break.
Button
(When the pipe wouldn't expand / contract)
Pull the pipeup hard.
Vacuum power
adjustment ring
Vacuuming can continue.
Suction power decreases. Dust compartment
should be emptied.
Pull
Insert securely by turning
Angled pipe
Caution
Please do not place your hand on the extension pipe buttons during operation.
Please do push the button in when adjusting the length.
Power Control /
( SC-B555/B555T only/
SC-B555/B555T
(
Angled pipe
Set the POWER CONTROL to MAX for maximum suction.
In the position MIN the suction power is decreased.
Removal ring /
MAX
POWER CONTROL
MIN
/
Switch
SC-B555T only/
SC-B555T
Start or stop vacuum cleaner by pushing on the switch.
Handle
TURBO CLEANTM
/
Button
Hose stopper
Change the switch lever according to the area you want to vacuum.
Air inlet
Blower (Exhaust outlet) /
Hose
Pipe holder
High
Use blower to blow dust behind furniture, etc.
1. Insert the hose stopper into the exhaust outlet.
2. Press the switch.
The "TURBO CLEAN" turns at a high speed. It is
ideal for vacuuming on the rug when the switch
lever is selected to this position.
The crevice attachment can be used to blow dust.
LOW
HIGH
Low
Exhaust outlet
The "TURBO CLEAN" turns at a low speed. It is ideal
for vacuuming on the floor when the switch lever is
Switch Lever
selected to this position.
Attachments /
Floor Nozzle /
Cord Rewind Button /
The two-way floor nozzle has lever with two
positions.
Caution
To pull the cord back into the unit, press the cord rewind button.
The head of the brush can rotate.
Please do not vacuum on the floor while the switch lever is set
to "HIGH", as this may damage the floor.
Caution:
Hold the plug when rewinding the cord so that the plug does not damage furniture,
hands, the vacuum cleaner or the cord by hitting them.
Holding the plug will make rewinding smoother.
When the dust compartment is full, the TURBO CLEANTM may
turn slowly. Please empty the dust compartment.
FLOOR:
For vacuuming edges and gaps, and for
vacuuming fragile or easily scratched items.
For vacuuming wooden floors, linoleum or
plastic covered floors.
Cord and Plug /
Warning-To reduce the risk of injury, unplug before connecting the
TURBO CLEANTM
.
Pull out the cord and c
onnect the wall outlet.
Do not extend the cord from the unit beyond the red
marker line.
Put the dusting brush
here when not in use.
RUG:
For vacuuming rugs and carpets.
Cord rewind button
DUST DISPOSAL /
If there is a reduction in suction power, turn off the vacuum cleaner, disconnect the hose and
proceed as follows:
1. To separate the dust compartment
from the vacuum cleaner, push the
clamp button as shown.
Dust compartment
Clamp button
2. To remove the filter.
Caution:
Remove the filter slowly
to prevent the dust
from falling out.
3. Removing the dirt.
Caution:
If the dust is packed tightly and
difficult to remove, lightly tap the
dust compartment.
4. Slide the lever in the direction of
the arrows to remove the dust
Lever
by shaking.
5. Hold the clamp to open up the
pre-filter and empty the dirt out
of the filter.
Clamp
Filter
Pre-filter
6. To reassemble the unit.
Insert the filter in the dust
compartment.
Then attach the dust
compartment section
to the motor section.
Thank you for your purchase of the Sanyo Vacuum Cleaner.
Please read these instructions carefully before using.
A FEW PRECAUTIONS
1. Operation without the dust compartment and /or filters in place will allow
dust to enter the motor and could damage the vacuum cleaner.
2. Keep the vacuum cleaner away from stoves and other heat sources.
Heat can deform and discolor the plastic parts of the unit.
3. Keep the vacuum cleaner free of insecticides. Do not wipe with benzine,
thinner, petrol or other oils which might cause discoloration or cracking.
To clean the body and hose, dampen a cloth with a mild detergent and
wipe clean.
4. Blocking the suction inlet or allowing the dust to clog the hose will
decrease the efficiency of the motor.
5. Be sure not to push the clamp button while carrying the vacuum cleaner.
6. Never try to vacuum the following objects. They may damage the unit or
cause a fire.
* Wet things, mud, soil, and fluids
* Burning cigarettes
* Needles and razor blades
* Inflammable materials such as gasoline and thinner
* Construction rubbish
7. The following kinds of treatment shorten hose life:
* Bending hose at an acute angle when storing
* Pulling the hose with excessive force
* Placing heavy objects on, or stepping on the hose
8. Pull out the plug from the power source after use. Grasp the plug not
the cord when pulling out the plug.
Pulling on the cord may lead to shortcircuiting.
9. Long and continuous use causes the exhaust air and the body of the
vacuum cleaner to become warm. This, however, does not denote
malfunction.
10. When vacuuming places that are very dusty, and also when vacuuming
regularly, empty the dust compartment before it becomes completely
filled.
Frequent emptying lengthens the life of the motor and maintains strong
suction power.
11.
If the supply cord of this appliance is damaged, it must only be replaced
by the manufacturer, its designated repair shop, or a professional, in
order to avoid a hazard.
12. Do not allow it to be used as a toy. Close attention is necessary when
used by or near children or infirm persons.
13. Unplug the appliance from outlet before cleaning or maintaining.
14.This appliance is not intended for use by persons (including children with
ruduced physical, sensory or mental capabilities, or lack of knowledge,
unless they have been given supervision or instruction concerning use
of the appliance by a person responsible for their safety.
15.Children should be supervised to ensure they do not paly with the appliance.
HOW TO USE THE HOSE STAND /
Shorten the extension
pipe.
1
Hold here
Wind
2
2
Stand the vacuum
cleaner up and insert t
he pipe holder into the
pipe-holder hole.
Pipe holder
3
Hold the hose and
wind it around
the pipe.
1
Pipe holder hole
Caution
Do not carry the vacuum
cleaner while it is in the
storage position.
(Injury or damage may result
if the hose or coupling pipe
becomes unattached.)
FILTER CARE /
When the suction power is low and the dust has been discarded, the filter still should be cleaned.
1. Slide the lever in the direction of
the arrows to remove the dust
Lever
by shaking.
2. Lightly tap the filter to
remove the dust.
If you are concerned about dust on the filter:
1. Wash the filter with water.
If the dust is not easily removed, use a
brush for removal.
2. Dry the filter thoroughly.
Caution:
Do not dry in direct sunlight or
by heating, as the filter may
become damage. Never put the
filter into the vacuum cleaner
unless it is completely dry.
To assure the best results, we recommend cleaning the filters once every one (1) year,
depending on usage.
CARE OF TURBO CLEANTM
/
Before caring for the TURBO CLEANTM , be sure to turn OFF the switch of the unit and disconnect
the plug from the outlet.
If needles, pins or waste paper get stuck in the suction inlet, remove them after going through
the above procedure.
Trying to remove them during operation is dangerous.
EDGE GRABBERTM
/
The Edge Grabber system is designed to help
clean all the way up to the baseboards. The
suction shutter is opened when the floor
nozzle is pushed against the wall.
Edge grabber
CARE AND MAINTENANCE
If you have a problem with your vacuum cleaner, consult the handy guide below. If the
vacuum cleaner is malfunctioning, do not operate it. Contact your dealer or the nearest Sanyo
Service Center.
9BF-D-P111-08300 0812-
E/ARA
0
|